IPCDNNetwork Working Group A. AhmadInternet-Draft Protego Networks,Request for Comments: 4547 Cisco Systems Inc.Expires: July 12, 2005Category: Standards Track G. Nakanishi MotorolaJanuary 11, 2005June 2006 Event Notification Management Information Base forDOCSIS CompliantData over Cable Service Interface Specifications (DOCSIS)-Compliant Cable Modems and Cable Modem Termination Systemsdraft-ietf-ipcdn-docsisevent-mib-06Status ofthisThis Memo This documentisspecifies anInternet-Draft and is subject to all provisions of section 3 of RFC 3667. By submitting this Internet-Draft, each author represents that any applicable patent or other IPR claims of which he or she is aware have been or will be disclosed, and any of which he or she become aware will be disclosed, in accordance with RFC 3668. Internet-Drafts are working documents ofInternet standards track protocol for the InternetEngineering Task Force (IETF), its areas,community, andits working groups. Note that other groups may also distribute working documents as Internet-Drafts. Internet-Drafts are draft documents validrequests discussion and suggestions fora maximumimprovements. Please refer to the current edition ofsix monthsthe "Internet Official Protocol Standards" (STD 1) for the standardization state andmay be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress." The liststatus ofcurrent Internet-Drafts can be accessed at http://www.ietf.org/ietf/1id-abstracts.txt. The listthis protocol. Distribution ofInternet-Draft Shadow Directories can be accessed at http://www.ietf.org/shadow.html. This Internet-Draft will expire on July 12, 2005.this memo is unlimited. Copyright Notice Copyright (C) The Internet Society(2005).(2006). Abstract This memo defines a portion of the Management Information Base (MIB) for use with network management protocols in the Internet community. In particular, it defines a basic set of managed objects forSNMP-Simple Network Management Protocol (SNMP) based event notification management ofDOCSISData Over Cable Service Interface Specification (DOCSIS) compliant Cable Modems and Cable Modem Termination Systems. This MIB is defined as an extension to the DOCSIS Cable Device MIB. This memo specifies a MIB module in a manner that is compliant to theSMIv2.Structure of Management Information Version 2 (SMIv2). The set of objects is consistent with the SNMP framework and existing SNMP standards.This memo is a product of the IPCDN working group within the Internet Engineering Task Force. Comments are solicited and should be addressed to the working group's mailing list at ipcdn@ietf.org and/or the author.Table of Contents 1. The Internet-Standard Management Framework. . . . . . . . . 3......................2 2. Glossary. . . . . . . . . . . . . . . . . . . . . . . . . . 3 2.1........................................................2 2.1. BPI - Baseline Privacy Interface. . . . . . . . . . . . . 3 2.2...........................3 2.2. BPI - Baseline Privacy Plus Interface. . . . . . . . . . 3 2.3......................3 2.3. CATV. . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2.4.......................................................3 2.4. CM - Cable Modem. . . . . . . . . . . . . . . . . . . . . 3 2.5...........................................3 2.5. CMTS - Cable Modem Termination System. . . . . . . . . . 3 2.6......................3 2.6. DOCSIS. . . . . . . . . . . . . . . . . . . . . . . . . . 4 2.7.....................................................3 2.7. Downstream. . . . . . . . . . . . . . . . . . . . . . . . 4 2.8.................................................4 2.8. Head-end. . . . . . . . . . . . . . . . . . . . . . . . . 4 2.9...................................................4 2.9. MAC Packet. . . . . . . . . . . . . . . . . . . . . . . . 4 2.10.................................................4 2.10. RF. . . . . . . . . . . . . . . . . . . . . . . . . . . 4 2.11........................................................4 2.11. SID. . . . . . . . . . . . . . . . . . . . . . . . . . 4 2.12.......................................................4 2.12. TLV. . . . . . . . . . . . . . . . . . . . . . . . . . 4 2.13.......................................................4 2.13. Upstream. . . . . . . . . . . . . . . . . . . . . . . . 5..................................................4 3. Overview. . . . . . . . . . . . . . . . . . . . . . . . . . 5 3.1........................................................4 3.1. Structure of the MIB. . . . . . . . . . . . . . . . . . . 5.......................................5 4. Definitions. . . . . . . . . . . . . . . . . . . . . . . . 6.....................................................5 5. Contributors. . . . . . . . . . . . . . . . . . . . . . . . 37...................................................35 6.Acknowledgments . . . . . . . . . . . . . . . . . . . . . . 37Acknowledgements ...............................................36 7. SecurityConsideration . . . . . . . . . . . . . . . . . . . 37Considerations ........................................36 8. IANA Considerations. . . . . . . . . . . . . . . . . . . . 38............................................37 9. References. . . . . . . . . . . . . . . . . . . . . . . . . 38 9.1.....................................................37 9.1. Normative References. . . . . . . . . . . . . . . . . . . . 38 9.2......................................37 9.2. Informative References. . . . . . . . . . . . . . . . . . . 40 Authors' Addresses . . . . . . . . . . . . . . . . . . . . . 40 Intellectual Property and Copyright Statements . . . . . . . 41....................................38 1. The Internet-Standard Management Framework For a detailed overview of the documents that describe the current Internet-Standard Management Framework, please refer to section 7 of RFC 3410 [16]. Managed objects are accessed via a virtual information store, termed the Management Information Base or MIB. MIB objects are generally accessed through the Simple Network Management Protocol (SNMP). Objects in the MIB are defined using the mechanisms defined in the Structure of Management Information (SMI). This memo specifies a MIB module that is compliant to the SMIv2, which is described in STD 58, RFC 2578 [2], STD 58, RFC 2579 [3] and STD 58, RFC 2580 [4]. 2. Glossary The terms in this document are derived either from normal cable system usage, or from the documents associated with the Data Over Cable Service Interface Specification (DOCSIS) process.2.12.1. BPI - Baseline Privacy Interface A mechanism for providing data privacy over the HFC network in DOCSIS 1.0systems[8]. 2.2systems [8]. 2.2. BPI - Baseline Privacy Plus Interface A mechanism thatextendextends the Baseline Privacy Interface with the addition of CM authentication over the HFC network inDOCSIS1.1/2.0 systemDOCSIS 1.1/2.0 systems and beyond [9].2.32.3. CATV Originally "Community Antenna Television", now used to refer to any cable or hybrid fiber and cable system used to deliver video signals to a community.2.42.4. CM - Cable Modem A CM acts as a "slave" station in aDOCSIS compliantDOCSIS-compliant cable data system.2.52.5. CMTS - Cable Modem Termination System A generic term covering a cable bridge or cable router in a head-end. A CMTS acts as the master station in aDOCSIS compliantDOCSIS-compliant cable data system. It is the only station that transmits downstream, and it controls the scheduling of upstream transmissions by its associated CMs.2.62.6. DOCSIS DOCSIS stands for"Data-Over-Cable"Data-over-Cable Service Interface Specifications" and refers to the ITU-T J.112 Annex B standard for cable modem systems [10], [13] commonly known as DOCSIS 1.0. The DOCSIS 1.1 specification is an extension of DOCSIS 1.0, with new features to support quality of service, fragmentation, and requirements for European cable plants [14]. DOCSIS 2.0 [15] builds upon DOCSIS1.1,1.1 and provides all of the features and functionality that DOCSIS 1.1 provides. In addition, it provides some significant enhancements in upstream capacity over DOCSIS 1.1, such as 30.72 Mbps maximum upstream channel capacity, Synchronous-Code Division Multiple Access (CDMA) operation, increased robustness to upstream noise and channel impairments, EnhancedReed-SolomonReed- Solomon errorcorrection and,correction, and Trellis Coded Modulation.2.72.7. Downstream The direction from the CMTS to the CM.2.82.8. Head-end The origination point in most cable systems of the subscriber video signals. Generally also the location of the CMTS equipment.2.92.9. MAC Packet A term referring to DOCSIS Protocol Data Unit (PDU).2.102.10. RF A term referring to Radio Frequency.2.112.11. SID A term referring to DOCSIS Service ID. The SID identifies a particular upstream bandwidth allocation and class-of-service management for DOCSIS, and identifies a particular bidirectional security association for BPI.2.122.12. TLV TLV stands for Type/Length/Value. TLV is an encoding method consisting of three fields. The first field indicates the type of element, the second field indicates the length of the element, and the third field contains the element's value.2.132.13. Upstream The direction from the CM to the CMTS. 3. Overview Offering High Speed Internet Serviceofferingin the cable industry has become extremely successful. DOCSIS devices are being deployed at a rate of multiple thousands per day. Although operators are enjoying successful deployment, they are also facingathe challengetoof properlymanagemanaging deployed devices. Operators are using Simple Network Management Protocol, a set of Management Information Base (MIB) required by DOCSIS, and SNMP Notifications to manage deployed DOCSIS devices. The usage of SNMP Notification for event reporting is becoming more popular as an effective and efficient method for network monitoring. Unfortunately, only a minimal set of SNMP Notifications is currently available. This notificationMIBMIB, in conjunction with [11] and[12] provide[12], provides a minimum set of standard DOCSIS Notifications that DOCSIS devices SHOULD support to enable successful management of DOCSIS devices andnetwork.networks. This document defines a set of objects required for the event notification management ofDOCSIS compliantDOCSIS-compliant Cable Modems (CMs) and Cable Modem Termination Systems (CMTSs). The MIB module is derived from the DOCSIS [11] and [12].TheAppendix H of [11] defines all DOCSIS 1.1 requiredeventsevents, andtheAppendix D of [12] does that for DOCSIS 2.0. The notifications specified in this document are used to notify these events via SNMP.TheIn this document, the key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL"in this documentare to be interpreted as described in RFC 2119 [1].3.13.1. Structure of the MIB This DOCS-IETF-CABLE-DEVICE-NOTIFICATION-MIB was designed to extend the RFC2669 [5] notification module. Two groups of SNMP notification objects are defined in this document. One group defines notifications for cable modem events, and the other group defines notifications for cable modem termination system events. DOCSIS defines numerouseventsevents, and each event is assigned to a functional category. This MIB defines a notification object for each functional category. The varbinding list of each notification includes information about the event that occurred on the device. 4. Definitions The MIB module defined here IMPORTs fromSNMPv2-SMI[2], SNMPv2-CONF[3],SNMPv2-SMI [2], SNMPv2-CONF [3], DOCS-CABLE-DEVICE-MIB [5], DOCS-IF-MIB [6], and IF-MIB [7]. DOCS-IETF-CABLE-DEVICE-NOTIFICATION-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, NOTIFICATION-TYPE, mib-2 FROM SNMPv2-SMI -- RFC 2578 MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP FROM SNMPv2-CONF -- RFC 2580 docsDevEvLevel, docsDevEvId, docsDevEvText, docsDevSwFilename, docsDevSwServer, docsDevServerDhcp, docsDevServerTime FROM DOCS-CABLE-DEVICE-MIB -- RFC 2669 docsIfCmCmtsAddress, docsIfCmtsCmStatusMacAddress, docsIfDocsisBaseCapability, docsIfCmStatusDocsisOperMode, docsIfCmStatusModulationType, docsIfCmtsCmStatusDocsisRegMode, docsIfCmtsCmStatusModulationType FROM DOCS-IF-MIB --draft-ietf-ipcdn-docs-rfmibv2-10 --RFCED.: replace 'draft-ietf-ipcdn-docs-rfmibv2-10' with assigned -- RFC number and remove this note.4546 ifPhysAddress FROM IF-MIB; -- RFC 2863 docsDevNotifMIB MODULE-IDENTITY LAST-UPDATED"200501110000Z""200605240000Z" --January 11, 2005May 24, 2006 ORGANIZATION "IETF IP over Cable Data Network Working Group" CONTACT-INFO " Azlina Ahmad Postal:Protego Networks,Cisco Systems, Inc.1064 Yosemite170 West Tasman DriveMilpitas,San Jose, CA95035,95134, U.S.A. Phone: 408262 5220853 7927 E-mail:azlina@protegonetworks.comazlina@cisco.com Greg Nakanishi Postal: Motorola 6450 Sequence Drive San Diego, CA 92121, U.S.A. Phone: 858 404 2366 E-mail: gnakanishi@motorola.com IETF IPCDN Working Group General Discussion: ipcdn@ietf.org Subscribe: http://www.ietf.org/mailman/listinfo/ipcdn Archive: ftp://ftp.ietf.org/ietf-mail-archive/ipcdn Co-chairs: Richard Woundy, richard_woundy@cable.comcast.com Jean-Francois Mule, jf.mule@cablelabs.com" DESCRIPTION "The Event Notification MIB is an extension of the CABLE DEVICE MIB. It defines various notification objects for both cable modem and cable modem termination systems. Two groups of SNMP notification objects are defined. One group is for notifying cable modemeventsevents, and one group is for notifying cable modem termination system events. DOCSIS defines numerouseventsevents, and each event is assigned to a functional category. This MIB defines a notification object for each functional category. The varbinding list of each notification includes information about the event that occurred on the device. Copyright (C) The Internet Society(2005).(2006). This version of this MIB module is part of RFCyyyy;4547; see the RFC itself for full legal notices."-- RFC Ed.: replace yyyy with actual RFC number & remove this noteREVISION"200501110000Z""200605240000Z" --January 11, 2005May 24, 2006 DESCRIPTION "Initial version, published as RFCyyyy." -- RFC Ed.: replace yyyy with actual RFC number & remove this note4547." ::= { mib-2xxx132 }-- Editor's Note (to be removed prior to publication): -- the IANA is requested to assign a value for "xxx" under -- the 'mib-2'subtree and to record the assignment in the -- SMI Numbers registry. -- When the assignment has been made, the RFC Editor is asked to -- replace "xxx" (here and in the MIB module) with the assigned -- value and to remove this note.docsDevNotifControl OBJECT IDENTIFIER ::= { docsDevNotifMIB 1} docsDevCmNotifs OBJECT IDENTIFIER ::= { docsDevNotifMIB 2 0 } docsDevCmtsNotifs OBJECT IDENTIFIER ::= { docsDevNotifMIB 3 0 } docsDevCmNotifControl OBJECT-TYPE SYNTAX BITS { cmInitTLVUnknownNotif( 0), cmDynServReqFailNotif( 1), cmDynServRspFailNotif( 2), cmDynServAckFailNotif( 3), cmBpiInitNotif( 4), cmBPKMNotif( 5), cmDynamicSANotif( 6), cmDHCPFailNotif( 7), cmSwUpgradeInitNotif( 8), cmSwUpgradeFailNotif( 9), cmSwUpgradeSuccessNotif( 10), cmSwUpgradeCVCNotif( 11), cmTODFailNotif( 12), cmDCCReqFailNotif( 13), cmDCCRspFailNotif( 14), cmDCCAckFailNotif( 15) } MAX-ACCESS read-write STATUS current DESCRIPTION "The object is used to enable specific CM notifications. For example, if the first bit is set, then docsDevCmInitTLVUnknownNotif is enabled. If it is not set, the notification is disabled. Note that notifications are also under the control of the MIB modules defined in RFC3413. If the device is rebooted,the value of this object SHOULD revert to the default value. " DEFVAL { {} } ::= { docsDevNotifControl 1 } docsDevCmtsNotifControl OBJECT-TYPE SYNTAX BITS { cmtsInitRegReqFailNotif( 0), cmtsInitRegRspFailNotif( 1), cmtsInitRegAckFailNotif( 2), cmtsDynServReqFailNotif( 3), cmtsDynServRspFailNotif( 4), cmtsDynServAckFailNotif( 5), cmtsBpiInitNotif( 6), cmtsBPKMNotif( 7), cmtsDynamicSANotif( 8), cmtsDCCReqFailNotif( 9), cmtsDCCRspFailNotif( 10), cmtsDCCAckFailNotif( 11) } MAX-ACCESS read-write STATUS current DESCRIPTION "The object is used to enable specific CMTS notifications. For example, if the first bit is set, then docsDevCmtsInitRegRspFailNotif is enabled. If it is not set, the notification is disabled. Note that notifications are also under the control of the MIB modules defined in RFC3413. If the device is rebooted,the value of this object SHOULD revert to the default value. " DEFVAL { {} } ::= { docsDevNotifControl 2 } docsDevCmInitTLVUnknownNotif NOTIFICATION-TYPE OBJECTS { docsDevEvLevel, docsDevEvId, docsDevEvText, ifPhysAddress, docsIfCmCmtsAddress, docsIfDocsisBaseCapability, docsIfCmStatusDocsisOperMode, docsIfCmStatusModulationType } STATUS current DESCRIPTION "Notification to indicate that an unknown TLV was encountered during the TLV parsing process. This notification sends additional information about the event by including the following objects init'sits varbinding list. - docsDevEvLevel: the priority level associated with the event. - docsDevEvId: the unique identifier of the event that occurred. - docsDevEvText: a textual description of the event. - ifPhysAddress: the MAC address of the cable interface of this cable modem. - docsIfCmCmtsAddress: the MAC address of the CMTS to which the CM is connectedto(if(if there is a cablecard/ interfacecard/interface in the CMTS, then it is actually the MAC address of the cable interface to whichconnected to.it is connected). - docsIfDocsisBaseCapability: the highest version of the DOCSISspecification(1.0,specification (1.0, 1.1, 2.0) that the device is capable of supporting. - docsIfCmStatusDocsisOperMode: the QOS level (1.0, 1.1) that the CM is operating in. -docsIfCmStatusModulationTypedocsIfCmStatusModulationType: the upstream modulation methodology used by theCM the CM).CM. " ::= { docsDevCmNotifs 1 } docsDevCmDynServReqFailNotif NOTIFICATION-TYPE OBJECTS { docsDevEvLevel, docsDevEvId, docsDevEvText, ifPhysAddress, docsIfCmCmtsAddress, docsIfDocsisBaseCapability, docsIfCmStatusDocsisOperMode, docsIfCmStatusModulationType } STATUS current DESCRIPTION "A notification to report the failure of a dynamic service request during the dynamic services process. This notification sends additional information about the event by including the following objects init'sits varbinding list. - docsDevEvLevel: the priority level associated with the event. - docsDevEvId: the unique identifier of the event that occurred. - docsDevEvText: a textual description of the event. - ifPhysAddress: the MAC address of the cable interface of this cable modem. - docsIfCmCmtsAddress: the MAC address of the CMTS to which the CM is connectedto(ifto (if there is a cablecard/ interfacecard/interface in the CMTS, then it is actually the MAC address of the cable interface to whichconnected to.it is connected). - docsIfDocsisBaseCapability: the highest version of the DOCSISspecification(1.0,specification (1.0, 1.1, 2.0) that the device is capable of supporting. - docsIfCmStatusDocsisOperMode: the QOS level (1.0, 1.1) that the CM is operating in. -docsIfCmStatusModulationTypedocsIfCmStatusModulationType: the upstream modulation methodology used by theCM the CM).CM. " ::= { docsDevCmNotifs 2 } docsDevCmDynServRspFailNotif NOTIFICATION-TYPE OBJECTS { docsDevEvLevel, docsDevEvId, docsDevEvText, ifPhysAddress, docsIfCmCmtsAddress, docsIfDocsisBaseCapability, docsIfCmStatusDocsisOperMode, docsIfCmStatusModulationType } STATUS current DESCRIPTION " A notification to report the failure of a dynamic service response during the dynamic services process. This notification sends additional information about the event by including the following objects init'sits varbinding list. - docsDevEvLevel: the priority level associated with the event. - docsDevEvId: the unique identifier of the event that occurred. - docsDevEvText: a textual description of the event. - ifPhysAddress: the MAC address of the cable interface of this cable modem. - docsIfCmCmtsAddress: the MAC address of the CMTS to which the CM is connectedto(if(if there is a cablecard/ interfacecard/interface in the CMTS, then it is actually the MAC address of the cable interface to whichconnected to.it is connected). - docsIfDocsisBaseCapability: the highest version of the DOCSISspecification(1.0,specification (1.0, 1.1, 2.0) that the device is capable of supporting. - docsIfCmStatusDocsisOperMode: the QOS level (1.0, 1.1) that the CM is operating in. -docsIfCmStatusModulationTypedocsIfCmStatusModulationType: the upstream modulation methodology used by theCM the CM).CM. " ::= { docsDevCmNotifs 3} docsDevCmDynServAckFailNotif NOTIFICATION-TYPE OBJECTS { docsDevEvLevel, docsDevEvId, docsDevEvText, ifPhysAddress, docsIfCmCmtsAddress, docsIfDocsisBaseCapability, docsIfCmStatusDocsisOperMode, docsIfCmStatusModulationType } STATUS current DESCRIPTION "A notification to report the failure of a dynamic service acknowledgement during the dynamic services process. This notification sends additional information about the event by including the following objects init'sits varbinding list. - docsDevEvLevel: the priority level associated with the event. - docsDevEvId: the unique identifier of the event that occurred. - docsDevEvText: a textual description of the event. - ifPhysAddress: the MAC address of the cable interface of this cable modem. - docsIfCmCmtsAddress: the MAC address of the CMTS to which the CM is connectedto(if(if there is a cablecard/ interfacecard/interface in the CMTS, then it is actually the MAC address of the cable interface to whichconnected to.it is connected). - docsIfDocsisBaseCapability: the highest version of the DOCSISspecification(1.0,specification (1.0, 1.1, 2.0) that the device is capable of supporting. - docsIfCmStatusDocsisOperMode: the QOS level (1.0, 1.1) that the CM is operating in. -docsIfCmStatusModulationTypedocsIfCmStatusModulationType: the upstream modulation methodology used by theCM the CM).CM. " ::= { docsDevCmNotifs 4} docsDevCmBpiInitNotif NOTIFICATION-TYPE OBJECTS { docsDevEvLevel, docsDevEvId, docsDevEvText, ifPhysAddress, docsIfCmCmtsAddress, docsIfDocsisBaseCapability, docsIfCmStatusDocsisOperMode, docsIfCmStatusModulationType } STATUS current DESCRIPTION "A notification to report the failure of a BPI initialization attempt during the registration process. This notification sends additional information about the event by including the following objects init'sits varbinding list. - docsDevEvLevel: the priority level associated with the event. - docsDevEvId: the unique identifier of the event that occurred. - docsDevEvText: a textual description of the event. - ifPhysAddress: the MAC address of the cable interface of this cable modem. - docsIfCmCmtsAddress: the MAC address of the CMTS to which the CM is connectedto(if(if there is a cablecard/ interfacecard/interface in the CMTS, then it is actually the MAC address of the cable interface to whichconnected to.it is connected). - docsIfDocsisBaseCapability: the highest version of the DOCSISspecification(1.0,specification (1.0, 1.1, 2.0) that the device is capable of supporting. - docsIfCmStatusDocsisOperMode: the QOS level (1.0, 1.1) that the CM is operating in. -docsIfCmStatusModulationTypedocsIfCmStatusModulationType: the upstream modulation methodology used by theCM the CM).CM. " ::= { docsDevCmNotifs 5 } docsDevCmBPKMNotif NOTIFICATION-TYPE OBJECTS { docsDevEvLevel, docsDevEvId, docsDevEvText, ifPhysAddress, docsIfCmCmtsAddress, docsIfDocsisBaseCapability, docsIfCmStatusDocsisOperMode, docsIfCmStatusModulationType } STATUS current DESCRIPTION "A notification to report the failure of a Baseline Privacy Key Management (BPKM) operation. This notification sends additional information about the event by including the following objects init'sits varbinding list. - docsDevEvLevel: the priority level associated with the event. - docsDevEvId: the unique identifier of the event that occurred. - docsDevEvText: a textual description of the event. - ifPhysAddress: the MAC address of the cable interface of this cable modem. - docsIfCmCmtsAddress: the MAC address of the CMTS to which the CM is connectedto(if(if there is a cablecard/ interfacecard/interface in the CMTS, then it is actually the MAC address of the cable interface to whichconnected to.it is connected). - docsIfDocsisBaseCapability: the highest version of the DOCSISspecification(1.0,specification (1.0, 1.1, 2.0) that the device is capable of supporting. - docsIfCmStatusDocsisOperMode: the QOS level (1.0, 1.1) that the CM is operating in. -docsIfCmStatusModulationTypedocsIfCmStatusModulationType: the upstream modulation methodology used by theCM the CM).CM. " ::= { docsDevCmNotifs 6 } docsDevCmDynamicSANotif NOTIFICATION-TYPE OBJECTS { docsDevEvLevel, docsDevEvId, docsDevEvText, ifPhysAddress, docsIfCmCmtsAddress, docsIfDocsisBaseCapability, docsIfCmStatusDocsisOperMode, docsIfCmStatusModulationType } STATUS current DESCRIPTION "A notification to report the failure of a dynamic security association operation. This notification sends additional information about the event by including the following objects init'sits varbinding list. - docsDevEvLevel: the priority level associated with the event. - docsDevEvId: the unique identifier of the event that occurred. - docsDevEvText: a textual description of the event. - ifPhysAddress: the MAC address of the cable interface of this cable modem. - docsIfCmCmtsAddress: the MAC address of the CMTS to which the CM is connectedto(if(if there is a cablecard/ interfacecard/interface in the CMTS, then it is actually the MAC address of the cable interface to whichconnected to.it is connected). - docsIfDocsisBaseCapability: the highest version of the DOCSISspecification(1.0,specification (1.0, 1.1, 2.0) that the device is capable of supporting. - docsIfCmStatusDocsisOperMode: the QOS level (1.0, 1.1) that the CM is operating in. -docsIfCmStatusModulationTypedocsIfCmStatusModulationType: the upstream modulation methodology used by theCM the CM).CM. " ::= { docsDevCmNotifs 7 } docsDevCmDHCPFailNotif NOTIFICATION-TYPE OBJECTS { docsDevEvLevel, docsDevEvId, docsDevEvText, ifPhysAddress, docsIfCmCmtsAddress, docsDevServerDhcp, docsIfDocsisBaseCapability, docsIfCmStatusDocsisOperMode, docsIfCmStatusModulationType } STATUS current DESCRIPTION "A notification to report the failure of a DHCP operation. This notification sends additional information about the event by including the following objects init'sits varbinding list. - docsDevEvLevel: the priority level associated with the event. - docsDevEvId: the unique identifier of the event that occurred. - docsDevEvText: a textual description of the event. - ifPhysAddress: the MAC address of the cable interface of this cable modem. - docsIfCmCmtsAddress: the MAC address of the CMTS to which the CM is connectedto(if(if there is a cablecard/ interfacecard/interface in the CMTS, then it is actually the MAC address of the cable interface to whichconnected to.it is connected). - docsDevServerDhcp: the IP address of the DHCP server. - docsIfDocsisBaseCapability: the highest version of the DOCSISspecification(1.0,specification (1.0, 1.1, 2.0) that the device is capable of supporting. - docsIfCmStatusDocsisOperMode: the QOS level (1.0, 1.1) that the CM is operating in. -docsIfCmStatusModulationTypedocsIfCmStatusModulationType: the upstream modulation methodology used by theCM the CM).CM. " ::= { docsDevCmNotifs 8 } docsDevCmSwUpgradeInitNotif NOTIFICATION-TYPE OBJECTS { docsDevEvLevel, docsDevEvId, docsDevEvText, ifPhysAddress, docsIfCmCmtsAddress, docsDevSwFilename, docsDevSwServer, docsIfDocsisBaseCapability, docsIfCmStatusDocsisOperMode, docsIfCmStatusModulationType } STATUS current DESCRIPTION "A notification to indicate that a software upgrade has been initiated on the device. This notification sends additional information about the event by including the following objects init'sits varbinding list. - docsDevEvLevel: the priority level associated with the event. - docsDevEvId: the unique identifier of the event that occurred. - docsDevEvText: a textual description of the event. - ifPhysAddress: the MAC address of the cable interface of this cable modem. - docsIfCmCmtsAddress: the MAC address of the CMTS to which the CM is connectedto(if(if there is a cablecard/ interfacecard/interface in the CMTS, then it is actually the MAC address of the cable interface to whichconnected to.it is connected). - docsIfDocsisBaseCapability: the highest version of the DOCSISspecification(1.0,specification (1.0, 1.1, 2.0) that the device is capable of supporting. - docsIfCmStatusDocsisOperMode: the QOS level (1.0, 1.1) that the CM is operating in. -docsIfCmStatusModulationTypedocsIfCmStatusModulationType: the upstream modulation methodology used by theCM the CM).CM. " ::= { docsDevCmNotifs 9 } docsDevCmSwUpgradeFailNotif NOTIFICATION-TYPE OBJECTS { docsDevEvLevel, docsDevEvId, docsDevEvText, ifPhysAddress, docsIfCmCmtsAddress, docsDevSwFilename, docsDevSwServer, docsIfDocsisBaseCapability, docsIfCmStatusDocsisOperMode, docsIfCmStatusModulationType } STATUS current DESCRIPTION "A notification to report the failure of a software upgrade attempt. This notification sends additional information about the event by including the following objects init'sits varbinding list. - docsDevEvLevel: the priority level associated with the event. - docsDevEvId: the unique identifier of the event that occurred. - docsDevEvText: a textual description of the event. - ifPhysAddress: the MAC address of the cable interface of this cable modem. - docsIfCmCmtsAddress: the MAC address of the CMTS to which the CM is connectedto(if(if there is a cablecard/ interfacecard/interface in the CMTS, then it is actually the MAC address of the cable interface to whichconnected to.it is connected). - docsDevSwFilename: the software image file name - docsDevSwServer: the IP address of the server that the image is retrieved from. - docsIfDocsisBaseCapability: the highest version of the DOCSISspecification(1.0,specification (1.0, 1.1, 2.0) that the device is capable of supporting. - docsIfCmStatusDocsisOperMode: the QOS level (1.0, 1.1) that the CM is operating in. -docsIfCmStatusModulationTypedocsIfCmStatusModulationType: the upstream modulation methodology used by theCM the CM).CM. " ::= { docsDevCmNotifs 10 } docsDevCmSwUpgradeSuccessNotif NOTIFICATION-TYPE OBJECTS { docsDevEvLevel, docsDevEvId, docsDevEvText, ifPhysAddress, docsIfCmCmtsAddress, docsDevSwFilename, docsDevSwServer, docsIfDocsisBaseCapability, docsIfCmStatusDocsisOperMode, docsIfCmStatusModulationType } STATUS current DESCRIPTION "A notification to report the software upgrade success status. This notification sends additional information about the event by including the following objects init'sits varbinding list. - docsDevEvLevel: the priority level associated with the event. - docsDevEvId: the unique identifier of the event that occurred. - docsDevEvText: a textual description of the event. - ifPhysAddress: the MAC address of the cable interface of this cable modem. - docsIfCmCmtsAddress: the MAC address of the CMTS to which the CM is connectedto(if(if there is a cablecard/ interfacecard/interface in the CMTS, then it is actually the MAC address of the cable interface to whichconnected to.it is connected). - docsDevSwFilename: the software image file name - docsDevSwServer: the IP address of the server that the image is retrieved from. - docsIfDocsisBaseCapability: the highest version of the DOCSISspecification(1.0,specification (1.0, 1.1, 2.0) that the device is capable of supporting. - docsIfCmStatusDocsisOperMode: the QOS level (1.0, 1.1) that the CM is operating in. -docsIfCmStatusModulationTypedocsIfCmStatusModulationType: the upstream modulation methodology used by theCM the CM).CM. " ::= { docsDevCmNotifs 11 } docsDevCmSwUpgradeCVCFailNotif NOTIFICATION-TYPE OBJECTS { docsDevEvLevel, docsDevEvId, docsDevEvText, ifPhysAddress, docsIfCmCmtsAddress, docsIfDocsisBaseCapability, docsIfCmStatusDocsisOperMode, docsIfCmStatusModulationType } STATUS current DESCRIPTION "A notification to report that the verification of the code file has failed during a secure software upgrade attempt. This notification sends additional information about the event by including the following objects init'sits varbinding list. - docsDevEvLevel: the priority level associated with the event. - docsDevEvId: the unique identifier of the event that occurred. - docsDevEvText: a textual description of the event. - ifPhysAddress: the MAC address of the cable interface of this cable modem. - docsIfCmCmtsAddress: the MAC address of the CMTS to which the CM is connectedto(if(if there is a cablecard/ interfacecard/interface in the CMTS, then it is actually the MAC address of the cable interface to whichconnected to.it is connected). - docsIfDocsisBaseCapability: the highest version of the DOCSISspecification(1.0,specification (1.0, 1.1, 2.0) that the device is capable of supporting. - docsIfCmStatusDocsisOperMode: the QOS level (1.0, 1.1) that the CM is operating in. -docsIfCmStatusModulationTypedocsIfCmStatusModulationType: the upstream modulation methodology used by theCM the CM).CM. " ::= { docsDevCmNotifs 12 } docsDevCmTODFailNotif NOTIFICATION-TYPE OBJECTS { docsDevEvLevel, docsDevEvId, docsDevEvText, ifPhysAddress, docsIfCmCmtsAddress, docsDevServerTime, docsIfDocsisBaseCapability, docsIfCmStatusDocsisOperMode, docsIfCmStatusModulationType } STATUS current DESCRIPTION "A notification to reportathe failure of a time of day operation. This notification sends additional information about the event by including the following objects init'sits varbinding list. - docsDevEvLevel: the priority level associated with the event. - docsDevEvId: the unique identifier of the event that occurred. - docsDevEvText: a textual description of the event. - ifPhysAddress: the MAC address of the cable interface of this cable modem. - docsIfCmCmtsAddress: the MAC address of the CMTS to which the CM is connectedto(if(if there is a cablecard/ interfacecard/interface in the CMTS, then it is actually the MAC address of the cable interface to whichconnected to.it is connected). - docsDevServerTime: the IP address of the time server. - docsIfDocsisBaseCapability: the highest version of the DOCSISspecification(1.0,specification (1.0, 1.1, 2.0) that the device is capable of supporting. - docsIfCmStatusDocsisOperMode: the QOS level (1.0, 1.1) that the CM is operating in. -docsIfCmStatusModulationTypedocsIfCmStatusModulationType: the upstream modulation methodology used by theCM the CM).CM. " ::= { docsDevCmNotifs 13 } docsDevCmDCCReqFailNotif NOTIFICATION-TYPE OBJECTS { docsDevEvLevel, docsDevEvId, docsDevEvText, ifPhysAddress, docsIfCmCmtsAddress, docsIfDocsisBaseCapability, docsIfCmStatusDocsisOperMode, docsIfCmStatusModulationType } STATUS current DESCRIPTION " A notification to reportathe failure of a dynamic channel change request during the dynamic channel change process on the CM. This notification sends additional information about the event by including the following objects init'sits varbinding list. - docsDevEvLevel: the priority level associated with the event. - docsDevEvId: the unique identifier of the event that occurred. - docsDevEvText: a textual description of the event. - ifPhysAddress: the MAC address of the cable interface of this cable modem. - docsIfCmCmtsAddress: the MAC address of the CMTS to which the CM is connectedto(if(if there is a cablecard/ interfacecard/interface in the CMTS, then it is actually the MAC address of the cable interface to whichconnected to.it is connected). - docsIfDocsisBaseCapability: the highest version of the DOCSISspecification(1.0,specification (1.0, 1.1, 2.0) that the device is capable of supporting. - docsIfCmStatusDocsisOperMode: the QOS level (1.0, 1.1) that the CM is operating in. -docsIfCmStatusModulationTypedocsIfCmStatusModulationType: the upstream modulation methodology used by theCM the CM).CM. " ::= { docsDevCmNotifs 14 } docsDevCmDCCRspFailNotif NOTIFICATION-TYPE OBJECTS { docsDevEvLevel, docsDevEvId, docsDevEvText, ifPhysAddress, docsIfCmCmtsAddress, docsIfDocsisBaseCapability, docsIfCmStatusDocsisOperMode, docsIfCmStatusModulationType } STATUS current DESCRIPTION "A notification to report the failure of a dynamic channel change response during the dynamic channel change process on the CM. This notification sends additional information about the event by including the following objects init'sits varbinding list. - docsDevEvLevel: the priority level associated with the event. - docsDevEvId: the unique identifier of the event that occurred. - docsDevEvText: a textual description of the event. - ifPhysAddress: the MAC address of the cable interface of this cable modem. - docsIfCmCmtsAddress: the MAC address of the CMTS to which the CM is connectedto(if(if there is a cablecard/ interfacecard/interface in the CMTS, then it is actually the MAC address of the cable interface to whichconnected to.it is connected). - docsIfDocsisBaseCapability: the highest version of the DOCSISspecification(1.0,specification (1.0, 1.1, 2.0) that the device is capable of supporting. - docsIfCmStatusDocsisOperMode: the QOS level (1.0, 1.1) that the CM is operating in. -docsIfCmStatusModulationTypedocsIfCmStatusModulationType: the upstream modulation methodology used by theCM the CM).CM. " ::= { docsDevCmNotifs 15 } docsDevCmDCCAckFailNotif NOTIFICATION-TYPE OBJECTS { docsDevEvLevel, docsDevEvId, docsDevEvText, ifPhysAddress, docsIfCmCmtsAddress, docsIfDocsisBaseCapability, docsIfCmStatusDocsisOperMode, docsIfCmStatusModulationType } STATUS current DESCRIPTION "A notification to report the failure of a dynamic channel change acknowledgement during the dynamic channel change process on the CM. This notification sends additional information about the event by including the following objects init'sits varbinding list. - docsDevEvLevel: the priority level associated with the event. - docsDevEvId: the unique identifier of the event that occurred. - docsDevEvText: a textual description of the event. - ifPhysAddress: the MAC address of the cable interface of this cable modem. - docsIfCmCmtsAddress: the MAC address of the CMTS to which the CM is connectedto(if(if there is a cablecard/ interfacecard/interface in the CMTS, then it is actually the MAC address of the cable interface to whichconnected to.it is connected). - docsIfDocsisBaseCapability: the highest version of the DOCSISspecification(1.0,specification (1.0, 1.1, 2.0) that the device is capable of supporting. - docsIfCmStatusDocsisOperMode: the QOS level (1.0, 1.1) that the CM is operating in. - docsIfCmtsCmStatusModulationType the upstream modulation methodology used by theCM the CM).CM. " ::= { docsDevCmNotifs 16} docsDevCmtsInitRegReqFailNotif NOTIFICATION-TYPE OBJECTS { docsDevEvLevel, docsDevEvId, docsDevEvText, docsIfCmtsCmStatusMacAddress, ifPhysAddress, docsIfCmtsCmStatusDocsisRegMode, docsIfDocsisBaseCapability, docsIfCmtsCmStatusModulationType } STATUS current DESCRIPTION "A notification to report the failure of a registration request from a CM during the CM initialization processandthat was detected on the CMTS. This notification sends additional information about the event by including the following objects init'sits varbinding list. - docsDevEvLevel: the priority level associated with the event. - docsDevEvId: the unique identifier of the event that occurred. - docsDevEvText: a textual description of the event. - docsIfCmtsCmStatusMacAddress: the MAC address of the CMforwith which this notification isassociated with.associated. - ifPhysAddress: the MAC address of the CMTS (if there is a cablecard/ interfacecard/interface in the CMTS, then it is actually the MAC address of the cable interfacewhichthat connected to the CM) cable interface connected to the CM. - docsIfCmtsCmStatusDocsisRegMode: the QOS level (1.0, 1.1) that the reporting CM is operating in. - docsIfDocsisBaseCapability: the highest version of the DOCSISspecification(1.0,specification (1.0, 1.1, 2.0) that the device is capable of supporting. -docsIfCmtsCmStatusModulationTypedocsIfCmtsCmStatusModulationType: the upstream modulation methodology used by the CM. " ::= { docsDevCmtsNotifs 1 } docsDevCmtsInitRegRspFailNotif NOTIFICATION-TYPE OBJECTS { docsDevEvLevel, docsDevEvId, docsDevEvText, docsIfCmtsCmStatusMacAddress, ifPhysAddress, docsIfCmtsCmStatusDocsisRegMode, docsIfDocsisBaseCapability, docsIfCmtsCmStatusModulationType } STATUS current DESCRIPTION "A notification to report the failure of a registration response during the CM initialization processandthat was detected by the CMTS. This notification sends additional information about the event by including the following objects init'sits varbinding list. - docsDevEvLevel: the priority level associated with the event. - docsDevEvId: the unique identifier of the event that occurred. - docsDevEvText: a textual description of the event. - docsIfCmtsCmStatusMacAddress: the MAC address of the CMforwith which this notification isassociated with.associated. - ifPhysAddress: the MAC address of the CMTS (if there is a cablecard/ interfacecard/interface in the CMTS, then it is actually the MAC address of the cable interfacewhichthat connected to the CM) cable interface connected to the CM. - docsIfCmtsCmStatusDocsisRegMode: the QOS level (1.0, 1.1) that the reporting CM is operating in. - docsIfDocsisBaseCapability: the highest version of the DOCSISspecification(1.0,specification (1.0, 1.1, 2.0) that the device is capable of supporting. -docsIfCmtsCmStatusModulationTypedocsIfCmtsCmStatusModulationType: the upstream modulation methodology used by the CM. " ::= { docsDevCmtsNotifs 2 } docsDevCmtsInitRegAckFailNotif NOTIFICATION-TYPE OBJECTS { docsDevEvLevel, docsDevEvId, docsDevEvText, docsIfCmtsCmStatusMacAddress, ifPhysAddress, docsIfCmtsCmStatusDocsisRegMode, docsIfDocsisBaseCapability, docsIfCmtsCmStatusModulationType } STATUS current DESCRIPTION "A notification to report the failure of a registration acknowledgement from the CM during the CM initialization processandthat was detected by the CMTS. This notification sends additional information about the event by including the following objects init'sits varbinding list. - docsDevEvLevel: the priority level associated with the event. - docsDevEvId: the unique identifier of the event that occurred. - docsDevEvText: a textual description of the event. - docsIfCmtsCmStatusMacAddress: the MAC address of the CMforwith which this notification isassociated with.associated. - ifPhysAddress: the MAC address of the CMTS (if there is a cablecard/ interfacecard/interface in the CMTS, then it is actually the MAC address of the cable interfacewhichthat connected to the CM) cable interface connected to the CM. - docsIfCmtsCmStatusDocsisRegMode: the QOS level (1.0, 1.1) that the reporting CM is operating in. - docsIfDocsisBaseCapability: the highest version of the DOCSISspecification(1.0,specification (1.0, 1.1, 2.0) that the device is capable of supporting. -docsIfCmtsCmStatusModulationTypedocsIfCmtsCmStatusModulationType: the upstream modulation methodology used by the CM. " ::= { docsDevCmtsNotifs 3 } docsDevCmtsDynServReqFailNotif NOTIFICATION-TYPE OBJECTS { docsDevEvLevel, docsDevEvId, docsDevEvText, docsIfCmtsCmStatusMacAddress, ifPhysAddress, docsIfCmtsCmStatusDocsisRegMode, docsIfDocsisBaseCapability, docsIfCmtsCmStatusModulationType } STATUS current DESCRIPTION "A notification to report the failure of a dynamic service request during the dynamic services processandthat was detected by the CMTS. This notification sends additional information about the event by including the following objects init'sits varbinding list. - docsDevEvLevel: the priority level associated with the event. - docsDevEvId: the unique identifier of the event that occurred. - docsDevEvText: a textual description of the event. - docsIfCmtsCmStatusMacAddress: the MAC address of the CMforwith which this notification isassociated with.associated. - ifPhysAddress: the MAC address of the CMTS (if there is a cablecard/ interfacecard/interface in the CMTS, then it is actually the MAC address of the cable interfacewhichthat connected to the CM) cable interface connected to the CM. - docsIfCmtsCmStatusDocsisRegMode: the QOS level (1.0, 1.1) that the reporting CM is operating in. - docsIfDocsisBaseCapability: the highest version of the DOCSISspecification(1.0,specification (1.0, 1.1, 2.0) that the device is capable of supporting. -docsIfCmtsCmStatusModulationTypedocsIfCmtsCmStatusModulationType: the upstream modulation methodology used by the CM. " ::= { docsDevCmtsNotifs 4 } docsDevCmtsDynServRspFailNotif NOTIFICATION-TYPE OBJECTS { docsDevEvLevel, docsDevEvId, docsDevEvText, docsIfCmtsCmStatusMacAddress, ifPhysAddress, docsIfCmtsCmStatusDocsisRegMode, docsIfDocsisBaseCapability, docsIfCmtsCmStatusModulationType } STATUS current DESCRIPTION "A notification to report the failure of a dynamic service response during the dynamic services processandthat was detected by the CMTS. This notification sends additional information about the event by including the following objects init'sits varbinding list. - docsDevEvLevel: the priority level associated with the event. - docsDevEvId: the unique identifier of the event that occurred. - docsDevEvText: a textual description of the event. - docsIfCmtsCmStatusMacAddress: the MAC address of the CMforwith which this notification isassociated with.associated. - ifPhysAddress: the MAC address of the CMTS (if there is a cablecard/ interfacecard/interface in the CMTS, then it is actually the MAC address of the cable interfacewhichthat connected to the CM) cable interface connected to the CM. - docsIfCmtsCmStatusDocsisRegMode: the QOS level (1.0, 1.1) that the reporting CM is operating in. - docsIfDocsisBaseCapability: the highest version of the DOCSISspecification(1.0,specification (1.0, 1.1, 2.0) that the device is capable of supporting. -docsIfCmtsCmStatusModulationTypedocsIfCmtsCmStatusModulationType: the upstream modulation methodology used by the CM. " ::= { docsDevCmtsNotifs 5 } docsDevCmtsDynServAckFailNotif NOTIFICATION-TYPE OBJECTS { docsDevEvLevel, docsDevEvId, docsDevEvText, docsIfCmtsCmStatusMacAddress, ifPhysAddress, docsIfCmtsCmStatusDocsisRegMode, docsIfDocsisBaseCapability, docsIfCmtsCmStatusModulationType } STATUS current DESCRIPTION "A notification to report the failure of a dynamic service acknowledgement during the dynamic services processandthat was detected by the CMTS. This notification sends additional information about the event by including the following objects init'sits varbinding list. - docsDevEvLevel: the priority level associated with the event. - docsDevEvId: the unique identifier of the event that occurred. - docsDevEvText: a textual description of the event. - docsIfCmtsCmStatusMacAddress: the MAC address of the CMforwith which this notification isassociated with.associated. - ifPhysAddress: the MAC address of the CMTS (if there is a cablecard/ interfacecard/interface in the CMTS, then it is actually the MAC address of the cable interfacewhichthat connected to the CM) cable interface connected to the CM. - docsIfCmtsCmStatusDocsisRegMode: the QOS level (1.0, 1.1) that the reporting CM is operating in. - docsIfDocsisBaseCapability: the highest version of the DOCSISspecification(1.0,specification (1.0, 1.1, 2.0) that the device is capable of supporting. -docsIfCmtsCmStatusModulationTypedocsIfCmtsCmStatusModulationType: the upstream modulation methodology used by the CM. " ::= { docsDevCmtsNotifs 6 } docsDevCmtsBpiInitNotif NOTIFICATION-TYPE OBJECTS { docsDevEvLevel, docsDevEvId, docsDevEvText, docsIfCmtsCmStatusMacAddress, ifPhysAddress, docsIfCmtsCmStatusDocsisRegMode, docsIfDocsisBaseCapability, docsIfCmtsCmStatusModulationType } STATUS current DESCRIPTION "A notification to report the failure of a BPI initialization attempt during the CM registration processandthat was detected by the CMTS. This notification sends additional information about the event by including the following objects init'sits varbinding list. - docsDevEvLevel: the priority level associated with the event. - docsDevEvId: the unique identifier of the event that occurred. - docsDevEvText: a textual description of the event. - docsIfCmtsCmStatusMacAddress: the MAC address of the CMforwith which this notification isassociated with.associated. - ifPhysAddress: the MAC address of the CMTS (if there is a cablecard/ interfacecard/interface in the CMTS, then it is actually the MAC address of the cable interfacewhichthat connected to the CM) cable interface connected to the CM. - docsIfCmtsCmStatusDocsisRegMode: the QOS level (1.0, 1.1) that the reporting CM is operating in. - docsIfDocsisBaseCapability: the highest version of the DOCSISspecification(1.0,specification (1.0, 1.1, 2.0) that the device is capable of supporting. -docsIfCmtsCmStatusModulationTypedocsIfCmtsCmStatusModulationType: the upstream modulation methodology used by the CM. " ::= { docsDevCmtsNotifs 7 } docsDevCmtsBPKMNotif NOTIFICATION-TYPE OBJECTS { docsDevEvLevel, docsDevEvId, docsDevEvText, docsIfCmtsCmStatusMacAddress, ifPhysAddress, docsIfCmtsCmStatusDocsisRegMode, docsIfDocsisBaseCapability, docsIfCmtsCmStatusModulationType } STATUS current DESCRIPTION "A notification to report the failure of a BPKM operationwhichthat is detected by the CMTS. This notification sends additional information about the event by including the following objects init'sits varbinding list. - docsDevEvLevel: the priority level associated with the event. - docsDevEvId: the unique identifier of the event that occurred. - docsDevEvText: a textual description of the event. - docsIfCmtsCmStatusMacAddress: the MAC address of the CMforwith which this notification isassociated with.associated. - ifPhysAddress: the MAC address of the CMTS (if there is a cablecard/ interfacecard/interface in the CMTS, then it is actually the MAC address of the cable interfacewhichthat connected to the CM) cable interface connected to the CM. - docsIfCmtsCmStatusDocsisRegMode: the QOS level (1.0, 1.1) that the reporting CM is operating in. - docsIfDocsisBaseCapability: the highest version of the DOCSISspecification(1.0,specification (1.0, 1.1, 2.0) that the device is capable of supporting. -docsIfCmtsCmStatusModulationTypedocsIfCmtsCmStatusModulationType: the upstream modulation methodology used by the CM. " ::= { docsDevCmtsNotifs 8 } docsDevCmtsDynamicSANotif NOTIFICATION-TYPE OBJECTS { docsDevEvLevel, docsDevEvId, docsDevEvText, docsIfCmtsCmStatusMacAddress, ifPhysAddress, docsIfCmtsCmStatusDocsisRegMode, docsIfDocsisBaseCapability, docsIfCmtsCmStatusModulationType } STATUS current DESCRIPTION "A notification to report the failure of a dynamic security association operationwhichthat is detected by the CMTS. This notification sends additional information about the event by including the following objects init'sits varbinding list. - docsDevEvLevel: the priority level associated with the event. - docsDevEvId: the unique identifier of the event that occurred. - docsDevEvText: a textual description of the event. - docsIfCmtsCmStatusMacAddress: the MAC address of the CMforwith which this notification isassociated with.associated. - ifPhysAddress: the MAC address of the CMTS (if there is a cablecard/ interfacecard/interface in the CMTS, then it is actually the MAC address of the cable interfacewhichthat connected to the CM) cable interface connected to the CM. - docsIfCmtsCmStatusDocsisRegMode: the QOS level (1.0, 1.1) that the reporting CM is operating in. - docsIfDocsisBaseCapability: the highest version of the DOCSISspecification(1.0,specification (1.0, 1.1, 2.0) that the device is capable of supporting. -docsIfCmtsCmStatusModulationTypedocsIfCmtsCmStatusModulationType: the upstream modulation methodology used by the CM. " ::= { docsDevCmtsNotifs 9 } docsDevCmtsDCCReqFailNotif NOTIFICATION-TYPE OBJECTS { docsDevEvLevel, docsDevEvId, docsDevEvText, docsIfCmtsCmStatusMacAddress, ifPhysAddress, docsIfCmtsCmStatusDocsisRegMode, docsIfDocsisBaseCapability, docsIfCmtsCmStatusModulationType } STATUS current DESCRIPTION "A notification to report the failure of a dynamic channel change request during the dynamic channel change process and is detected by the CMTS. This notification sends additional information about the event by including the following objects init'sits varbinding list. - docsDevEvLevel: the priority level associated with the event. - docsDevEvId: the unique identifier of the event that occurred. - docsDevEvText: a textual description of the event. - docsIfCmtsCmStatusMacAddress: the MAC address of the CMforwith which this notification isassociated with.associated. - ifPhysAddress: the MAC address of the CMTS (if there is a cablecard/ interfacecard/interface in the CMTS, then it is actually the MAC address of the cable interfacewhichthat connected to the CM) cable interface connected to the CM. - docsIfCmtsCmStatusDocsisRegMode: the QOS level (1.0, 1.1) that the reporting CM is operating in. - docsIfDocsisBaseCapability: the highest version of the DOCSISspecification(1.0,specification (1.0, 1.1, 2.0) that the device is capable of supporting. -docsIfCmtsCmStatusModulationTypedocsIfCmtsCmStatusModulationType: the upstream modulation methodology used by the CM. " ::= { docsDevCmtsNotifs 10 } docsDevCmtsDCCRspFailNotif NOTIFICATION-TYPE OBJECTS { docsDevEvLevel, docsDevEvId, docsDevEvText, docsIfCmtsCmStatusMacAddress, ifPhysAddress, docsIfCmtsCmStatusDocsisRegMode, docsIfDocsisBaseCapability, docsIfCmtsCmStatusModulationType } STATUS current DESCRIPTION "A notification to report the failure of a dynamic channel change response during the dynamic channel change process and is detected by the CMTS. This notification sends additional information about the event by including the following objects init'sits varbinding list. - docsDevEvLevel: the priority level associated with the event. - docsDevEvId: the unique identifier of the event that occurred. - docsDevEvText: a textual description of the event. - docsIfCmtsCmStatusMacAddress: the MAC address of the CMforwith which this notification isassociated with.associated. - ifPhysAddress: the MAC address of the CMTS (if there is a cablecard/ interfacecard/interface in the CMTS, then it is actually the MAC address of the cable interfacewhichthat connected to the CM) cable interface connected to the CM. - docsIfCmtsCmStatusDocsisRegMode: the QOS level (1.0, 1.1) that the reporting CM is operating in. - docsIfDocsisBaseCapability: the highest version of the DOCSISspecification(1.0,specification (1.0, 1.1, 2.0) that the device is capable of supporting. -docsIfCmtsCmStatusModulationTypedocsIfCmtsCmStatusModulationType: the upstream modulation methodology used by the CM. " ::= { docsDevCmtsNotifs 11 } docsDevCmtsDCCAckFailNotif NOTIFICATION-TYPE OBJECTS { docsDevEvLevel, docsDevEvId, docsDevEvText, docsIfCmtsCmStatusMacAddress, ifPhysAddress, docsIfCmtsCmStatusDocsisRegMode, docsIfDocsisBaseCapability, docsIfCmtsCmStatusModulationType } STATUS current DESCRIPTION "A notification to report the failure of a dynamic channel change acknowledgement during the dynamic channel change process and is detected by the CMTS. This notification sends additional information about the event by including the following objects init'sits varbinding list. - docsDevEvLevel: the priority level associated with the event. - docsDevEvId: the unique identifier of the event that occurred. - docsDevEvText: a textual description of the event. - docsIfCmtsCmStatusMacAddress: the MAC address of the CMforwith which this notification isassociated with.associated. - ifPhysAddress: the MAC address of the CMTS (if there is a cablecard/ interfacecard/interface in the CMTS, then it is actually the MAC address of the cable interfacewhichthat connected to the CM) cable interface connected to the CM. - docsIfCmtsCmStatusDocsisRegMode: the QOS level (1.0, 1.1) that the reporting CM is operating in. - docsIfDocsisBaseCapability: the highest version of the DOCSISspecification(1.0,specification (1.0, 1.1, 2.0) that the device is capable of supporting. -docsIfCmtsCmStatusModulationTypedocsIfCmtsCmStatusModulationType: the upstream modulation methodology used by the CM. " ::= { docsDevCmtsNotifs 12} -- --Conformance definitions -- docsDevNotifConformance OBJECT IDENTIFIER ::= { docsDevNotifMIB 4 } docsDevNotifGroups OBJECT IDENTIFIER ::= { docsDevNotifConformance 1 } docsDevNotifCompliances OBJECT IDENTIFIER ::= { docsDevNotifConformance 2 } docsDevCmNotifCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for CM Notifications andControl"Control." MODULE --docsDevNotif MANDATORY-GROUPS { docsDevCmNotifControlGroup, docsDevCmNotificationGroup } ::= { docsDevNotifCompliances 1 } docsDevCmNotifControlGroup OBJECT-GROUP OBJECTS { docsDevCmNotifControl } STATUS current DESCRIPTION "This group represents objectstothat allow control over CM Notifications." ::= { docsDevNotifGroups 1 } docsDevCmNotificationGroup NOTIFICATION-GROUP NOTIFICATIONS { docsDevCmInitTLVUnknownNotif, docsDevCmDynServReqFailNotif, docsDevCmDynServRspFailNotif, docsDevCmDynServAckFailNotif, docsDevCmBpiInitNotif, docsDevCmBPKMNotif, docsDevCmDynamicSANotif, docsDevCmDHCPFailNotif, docsDevCmSwUpgradeInitNotif, docsDevCmSwUpgradeFailNotif, docsDevCmSwUpgradeSuccessNotif, docsDevCmSwUpgradeCVCFailNotif, docsDevCmTODFailNotif, docsDevCmDCCReqFailNotif, docsDevCmDCCRspFailNotif, docsDevCmDCCAckFailNotif } STATUS current DESCRIPTION "A collection of CM notifications providing device status and control." ::= { docsDevNotifGroups 2 } docsDevCmtsNotifCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for DOCSIS CMTS Notification and Control." MODULE --docsDevNotif MANDATORY-GROUPS { docsDevCmtsNotifControlGroup, docsDevCmtsNotificationGroup } ::= { docsDevNotifCompliances 2 } docsDevCmtsNotifControlGroup OBJECT-GROUP OBJECTS { docsDevCmtsNotifControl } STATUS current DESCRIPTION "This group represents objectstothat allow control over CMTS Notifications." ::= { docsDevNotifGroups 3 } docsDevCmtsNotificationGroup NOTIFICATION-GROUP NOTIFICATIONS { docsDevCmtsInitRegReqFailNotif, docsDevCmtsInitRegRspFailNotif, docsDevCmtsInitRegAckFailNotif , docsDevCmtsDynServReqFailNotif, docsDevCmtsDynServRspFailNotif, docsDevCmtsDynServAckFailNotif, docsDevCmtsBpiInitNotif, docsDevCmtsBPKMNotif, docsDevCmtsDynamicSANotif, docsDevCmtsDCCReqFailNotif, docsDevCmtsDCCRspFailNotif, docsDevCmtsDCCAckFailNotif } STATUS current DESCRIPTION "A collection of CMTS notifications providing device status and control." ::= { docsDevNotifGroups 4 } END 5. Contributors Thanksgoesgo to the followingpeoplepeople, who have made significant contributions to this document: Junming Gao, Jean-Francois Mule, Dave Raftus, Pak Siripunkaw, and Rich Woundy. 6.AcknowledgmentsAcknowledgements This document was produced by the IPCDN Working Group. Thanks to Harrie Hazewinkel and Bert Wijnen for their thorough review and insightful comments on this document. Special thanks to Rich Woundy, who made several valuable suggestions to improve the notifications. 7. SecurityConsiderationConsiderations There are two management objects defined in this MIB module with a MAX-ACCESS clause of read-write and/or read-create (docsDevCmNotifControl and docsDevCmtsNotifControl). Such objects may be considered sensitive or vulnerable in some network environments. The support for SET operations in a non-secure environment without proper protection can have a negative effect on network operations. Setting docsDevCmNotifControl or docsDevCmtsNotifControl may cause flooding of notifications, which can disrupt network service. Besides causing "flooding", changing the objects can also mean that notifications will not be emittedwhilewhen oneintendedintends that to happen. This MIB defines a number of notification objects that send detailed information about the event that caused the generation of the notification. Informationincludedin the notification messageinclude:includes: event priority, the event Id, the event message body, the CM DOCSIS capability, the CM DOCSIS QOS level, the CM DOCSIS upstream modulation type, the cable interface MAC address of the cablemodem and,modem, and the cable card MAC address of the CMTS to which the modem is connected. The monitoring of these notification messages could be used to gather information about the state of the network and devices (CM and CMTS) attached to the network. SNMP versions prior to SNMPv3 did not include adequate security. Even if the network itself is secure (for example by using IPSec), eventhen,then there is no control as to who on the secure network is allowed to access and GET/SET (read/change/create/delete) the objects in this MIB module. It is RECOMMENDED that implementers consider the security features as provided by the SNMPv3 framework (see [16], section8),including8), including full support for the SNMPv3 cryptographic mechanisms (for authentication and privacy). Further, deployment of SNMP versions prior to SNMPv3 is NOT RECOMMENDED. Instead, it is RECOMMENDED to deploy SNMPv3 and to enable cryptographic security. It is then a customer/operator responsibility to ensure that the SNMP entity giving access to an instance of this MIB module is properly configured to give access to the objects only to those principals (users) that have legitimate rights to indeed GET or SET (change/create/delete) them. 8. IANA Considerations The MIB module defined in this document uses the following IANA- assigned OBJECT IDENTIFIER values recorded in the SMI Numbers registry: Descriptor OBJECT IDENTIFIER value ---------- ----------------------- docsDevNotifMIB { mib-2xxx132 }-- Editor's Note (to be removed prior to publication): the IANA is requested to assign a value for "xxx" under the 'mib-2' sub-tree and to record the assignment in the SMI Numbers registry. When the assignment has been made, the RFC Editor is asked to replace "xxx" (here and in the MIB module) with the assigned value and to remove this note.9. References9.19.1. Normative References [1] Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, March 1997. [2] McCloghrie, K., Perkins, D.,Schoenwaelder, J., Case, J., McCloghrie, K., Rose, M.andS. Waldbusser,J. Schoenwaelder, "Structure of Management Information Version 2 (SMIv2)", STD 58, RFC 2578, April 1999. [3] McCloghrie, K., Perkins, D.,Schoenwaelder, J., Case, J., McCloghrie, K., Rose, M.andS. Waldbusser,J. Schoenwaelder, "Textual Conventions for SMIv2", STD 58, RFC 2579, April 1999. [4] McCloghrie, K., Perkins,D.D., and J. Schoenwaelder, "Conformance Statements for SMIv2", STD 58, RFC 2580, April 1999. [5] St. Johns, M., "DOCSIS Cable Device MIB Cable Device Management Information Base for DOCSIS compliant Cable Modems and Cable Modem Termination Systems", RFC 2669, August 1999. [6] Raftus,D.,D. and E. Cardona, "Radio Frequency (RF) Interface Management Information Base forDOCSISData over Cable Service Interface Specifications (DOCSIS) 2.0compliantCompliant RFinterfaces", -- RFC ED.: replace this reference of 'draft-ietf-ipcdn-docs-rfmibv2-10' with actualInterfaces", RFCreference and remove this note.4546, June 2006. [7] McCloghrie, K. and F. Kastenholz, "The Interfaces Group MIB", RFC 2863, June 2000. [8] SCTE Data Standards Subcommittee, "Data-Over-Cable Service Interface Specifications: DOCSIS 1.0 Baseline Privacy Interface Specification SCTE 22-2", 2002, <http://www.scte.org/standards/>. [9] CableLabs, "Baseline Privacy Plus Interface SpecificationSP-BPI+040407",SP- BPI+040407", April 2004, <http://www.cablemodem.com/specifications/>. [10] SCTE Data Standards Subcommittee, "Data-Over-Cable Service Interface Specifications: DOCSIS 1.0 Operations Support System Interface Specification Radio Frequency Interface SCTE 22-3", 2002, <http://www.scte.org/standards/>. [11] CableLabs, "Data-Over-Cable Service Interface Specifications: Operations Support System Interface SpecificationSP-OSSIv1.1-I07-030703", July 2003,CM-SP- OSSIv1.1-C01-050907", September 2005, <http://www.cablemodem.com/specifications/>. [12] CableLabs, "Data-Over-Cable Service Interface Specifications: Operations Support System Interface SpecificationSP-OSSIv2.0-I07-041210", December 2004,CM-SP- OSSIv2.0-I09-050812", August 2005, <http://www.cablemodem.com/specifications/>. [13] SCTE Data Standards Subcommittee, "Data-Over-Cable Service Interface Specifications: DOCSIS 1.0 Radio Frequency Interface Specification SCTE 22-1", 2002, <http://www.scte.org/standards/>. [14] CableLabs, "Data-Over-Cable Service Interface Specifications: Radio Frequency Interface SpecificationSP-RFIv1.1-I10-030730", July 2003,CM-SP-RFIv1.1-C01- 050907", September 2005, <http://www.cablemodem.com/specifications/>. [15] CableLabs, "Data-Over-Cable Service Interface Specifications: Radio Frequency Interface SpecificationSP-RFIv2.0-I07-041210",CM-SP-RFIv2.0-I10- 051209", December2004,2005, <http://www.cablemodem.com/specifications/>.9.29.2. Informative References [16] Case, J., Mundy, R., Partain,D.D., and B. Stewart, "Introduction and Applicability Statements for Internet-Standard Management Framework", RFC 3410, December 2002. Authors' Addresses Azlina AhmadProtego Networks,Cisco Systems, Inc.1064 Yosemite170 West Tasman DriveMilpitas,San Jose, CA9503595134 US Phone: 408262 5220853 7927 EMail:azlina@protegonetworks.comazlina@cisco.com Greg Nakanishi Motorola 6450 Sequence Dr. San Diego, CA 92126 US Phone: 858 404-2366 EMail: gnakanishi@motorola.com Full Copyright Statement Copyright (C) The Internet Society (2006). This document is subject to the rights, licenses and restrictions contained in BCP 78, and except as set forth therein, the authors retain all their rights. This document and the information contained herein are provided on an "AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY AND THE INTERNET ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Intellectual PropertyStatementThe IETF takes no position regarding the validity or scope of any Intellectual Property Rights or other rights that might be claimed to pertain to the implementation or use of the technology described in this document or the extent to which any license under such rights might or might not be available; nor does it represent that it has made any independent effort to identify any such rights. Information on the procedures with respect to rights in RFC documents can be found in BCP 78 and BCP 79. Copies of IPR disclosures made to the IETF Secretariat and any assurances of licenses to be made available, or the result of an attempt made to obtain a general license or permission for the use of such proprietary rights by implementers or users of this specification can be obtained from the IETF on-line IPR repository at http://www.ietf.org/ipr. The IETF invites any interested party to bring to its attention any copyrights, patents or patent applications, or other proprietary rights that may cover technology that may be required to implement this standard. Please address the information to the IETF at ietf-ipr@ietf.org.Disclaimer of Validity This document and the information contained herein are provided on an "AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY AND THE INTERNET ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Copyright Statement Copyright (C) The Internet Society (2005). This document is subject to the rights, licenses and restrictions contained in BCP 78, and except as set forth therein, the authors retain all their rights. AcknowledgmentAcknowledgement Funding for the RFC Editor function iscurrentlyprovided by theInternet Society.IETF Administrative Support Activity (IASA).